Many Unix-like operating systems and distributions are tuned for desktop or light use out of the box and not for a production database. This guide describes recommended system performance tunings for operators of new and existing Riak clusters. The tunings present in this guide should be considered as a starting point. It is important to make note of what changes are made and when in order to measure the impact of those changes.
For performance and tuning recommendations specific to running Riak clusters on the Amazon Web Services EC2 environment, see AWS Performance Tuning.
Unless otherwise specified, the tunings recommended below are for Linux distributions. Users implementing Riak on BSD and Solaris distributions can use these tuning recommendations to make analogous changes in those operating systems.
Storage and File System Tuning
Due to the heavily I/O-focused profile of Riak, swap usage can result in
the entire server becoming unresponsive. We recommend setting
vm.swappiness to 0 in
/etc/sysctl.conf to prevent swapping as much
vm.swappiness = 0
Ideally, you should disable swap to ensure that Riak’s process pages are
not swapped. Disabling swap will allow Riak to crash in situations where
it runs out of memory. This will leave a crash dump file, named
erl_crash.dump, in the
/var/log/riak directory which can be used to
determine the cause of the memory usage.
Riak makes heavy use of disk I/O for its storage operations. It is
important that you mount volumes that Riak will be using for data
storage with the
noatime flag, meaning that filesystem
inodes on the volume will not be
touched when read. This flag can be set temporarily using the following
mount -o remount,noatime <riak_data_volume>
<riak_data_volume> in the above example with your actual Riak
data volume. The
noatime can be set in
/etc/fstab to mount
I/O or disk scheduling is a blanket term used to describe the method by which an operating system chooses how to order input and output operations to and from storage.
The default I/O scheduler (elevator) on Linux is completely fair queuing
cfq, which is designed for desktop use. While a good
general-purpose scheduler, is not designed to provide the kind of
throughput expected in production database deployments.
noopscheduler when deploying on iSCSI over HBAs, or any hardware-based RAID.
deadlinescheduler when using SSD-based storage.
To check the scheduler in use for block device
sda, for example, use
the following command:
To set the scheduler to
deadline, use the following command:
echo deadline > /sys/block/sda/queue/scheduler
The default I/O scheduler queue size is 128. The scheduler queue sorts writes in an attempt to optimize for sequential I/O and reduce seek time. Changing the depth of the scheduler queue to 1024 can increase the proportion of sequential I/O that disks perform and improve overall throughput.
To check the scheduler depth for block device
sda, use the following
To increase the scheduler depth to 1024, use the following command:
echo 1024 > /sys/block/sda/queue/nr_requests
At this time, Basho can recommend using ZFS on Solaris, SmartOS, and OmniOS. ZFS may work well with Riak on direct Solaris clones like IllumOS, but we cannot yet recommend this. ZFS on Linux is still too early in its project lifetime to be recommendable for production use due to concerns that have been raised about excessive memory use. ZFS on FreeBSD is more mature than ZFS on Linux, but Basho has not yet performed sufficient performance and reliability testing to recommend using ZFS and Riak on FreeBSD.
The ext4 file system defaults include two options that increase
integrity but slow performance. Because Riak’s integrity is based on
multiple nodes holding the same data, these two options can be changed
to boost I/O performance. We recommend setting
data=writeback when using the ext4 filesystem.
Similarly, the XFS file system defaults can be optimized to improve
performance. We recommend setting
allocsize=2M when using the XFS filesystem.
As with the
noatime setting, these settings should be added to
/etc/fstab so that they are persisted across server restarts.
Kernel and Network Tuning
The following settings are minimally sufficient to improve many aspects
of Riak usage on Linux, and should be added or updated in
net.ipv4.tcp_max_syn_backlog = 40000 net.core.somaxconn = 40000 net.core.wmem_default = 8388608 net.core.rmem_default = 8388608 net.ipv4.tcp_sack = 1 net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_fin_timeout = 15 net.ipv4.tcp_keepalive_intvl = 30 net.ipv4.tcp_tw_reuse = 1 net.ipv4.tcp_moderate_rcvbuf = 1
In general, these recommended values should be compared with the system defaults and only changed if benchmarks or other performance metrics indicate that networking is the bottleneck.
The following settings are optional, but may improve performance on a 10Gb network:
net.core.rmem_max = 134217728 net.core.wmem_max = 134217728 net.ipv4.tcp_mem = 134217728 134217728 134217728 net.ipv4.tcp_rmem = 4096 277750 134217728 net.ipv4.tcp_wmem = 4096 277750 134217728 net.core.netdev_max_backlog = 300000
Certain network interfaces ship with on-board features that have been
shown to hinder Riak network performance. These features can be disabled
For an Intel chipset NIC using the
driver running as
eth0, for example, run the following command:
ethtool -K eth0 lro off
For a Broadcom chipset NIC using the
bnx2 driver, run:
ethtool -K eth0 tso off
ethtool settings can be persisted across reboots by adding the above
command to the
Tuning these values will be required if they are changed, as they affect all network operations.
Optional I/O Settings
If your cluster is experiencing excessive I/O blocking, the following settings may help prevent disks from being overwhelmed during periods of high write activity at the expense of peak performance for spiky workloads:
vm.dirty_background_ratio = 0 vm.dirty_background_bytes = 209715200 vm.dirty_ratio = 40 vm.dirty_bytes = 0 vm.dirty_writeback_centisecs = 100 vm.dirty_expire_centisecs = 200
These settings have been tested and benchmarked by Basho in nodes with 16 GB of RAM.
Open Files Limit
Riak and supporting tools can consume a large number of open file handles during normal operation. For stability, increasing the number of open files limit is necessary. See Open Files Limit for more details.